Training Tips
1. Choose a suitable contact points and Silicone cap, and put it on the dog's neck.
2. If the hair is too thick, separate it by hand so that the Silicone cap touches the skin, making sure both electrodes touch the skin at the same time.
3. The tightness of the collar tied to the dog's neck is suitable for inserting a finger tie the collar on dog enough to fit a finger.
4. Shock training is not recommended for dogs under 6 months of age, aged, in poor health, pregnant, aggressive, or aggressive towards humans.
5. In order to make your pet less shocked by electric shock, it is recommended to use sound training first, then vibration, and finally use electric shock training. Then you can train your pet step by step.
6. The level of electric shock should start from level 1.
Important Safety Information
1. Disassembly of the collar is strictly prohibited under any circumstances, as it may destroy the waterproof function and thus void the product warranty.
2. If you want to test the electric shock function of the product, please use the delivered neon bulb for testing, do not test with your hands to avoid accidental injury.
3. Note that interference from the environment may cause the product to not work properly, such as high-voltage facilities, communication towers, thunderstorms and strong winds, large buildings, strong electromagnetic interference, etc.
Trouble shooting
1. When pressing buttons such as vibration or electric shock, and there is no response, you should first check:
1.1 Check if the remote control and collar are turned on.
1.2 Check whether the battery power of the remote control and collar is sufficient.
1.3 Check if the charger is 5V, or try another charging cable.
1.4 If the battery has not been used for a long time and the battery voltage is lower than the charging start voltage, it should be charged for a different period of time.
1.5 Verify that the collar is providing stimulation to your pet by placing a test light on the collar.
2. If the shock is weak, or has no effect on pets at all, you should check first.
2.1 Make sure that the contact points of the collar are snug against the pet's skin.
2.2 Try increasing the shock level.
3. If the remote control and collar do not respond or cannot receive signals, you should check first:
3.1 Check whether the remote control and the collar are successfully matched first.
3.2 If it cannot be paired, the collar and remote control should be fully charged first. The collar must be in the off state, and then long press the power button for 3 seconds to enter the red and green light flashing state before pairing (valid time is 30 seconds).
3.3 Check if the button of the remote control is pressed.
3.4 Check whether there is a electromagnetic field interference, strong signal etc. You can cancel the pairing first, and then re-pairing can automatically select a new channel to avoid interference.
4. The collar automatically emits sound, vibration, or electric shock signal, you can check first: check whether the remote control buttons are stuck.
Operating environment and maintenance
1. Do not operate the device in temperatures of 104°F and above.
2. Do not use the remote control when it is snowing, it may cause water ingress and damage the remote control.
3. Do not use this product in places with strong electromagnetic interference, which will seriously damage the performance of the product.
4. Avoid dropping the device on a hard surface or applying excessive pressure to it.
5. Do not use it in a corrosive environment, so as not to cause discoloration, deformation and other damage to the appearance of the product.
6. When not using this product, wipe the surface of the product clean, turn off the power, put it in the box, and put it in a cool and dry place.
7. The collar cannot be immersed in water for a long time.
8. If the remote control falls into the water, please take it out quickly and turn off the power, and then it can be used normally after drying the water.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
Measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and collar.
—Connect the equipment into an outlet on a circuit different from that to which the collar is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Post time: Oct-30-2023
