1. Keypad lock/Power button（
）.Short press to lock the button, and then short press to unlock. Long press the button for 2 secs to turn on/off.
2. Channel switch/Enter pairing button（
）, Short press to select the dog channel. Long press for 3 seconds to enter pairing mode.
3. Wireless Fence button(
): Short press to enter/exit the electronic fence. Note: This is an Exclusive function for X3, not available on X1/X2.
4. Vibration Level Decrease button:（
）
5. Vibration/Exit Pairing Mode button: (
) Short press to vibrate once, long press to vibrate 8 times and stop. During pairing mode,press this button to exit pairing.
6. Shock/Delete Pairing button(
): Short press to deliver a 1-second shock, long press to deliver an 8-second shock and stop. Release and press again to activate the shock. During pairing mode, select the receiver to delete pairing and press this button to delete.
7. Flashlight button(
)
8. Shock Level/Electronic Fence Level Increase button (▲).
9. Beep/Pairing Confirmation button(
): Short press to emit a beep sound. During pairing mode, select the dog channel and press this button to confirm pairing.
10. Vibration Level Increase button.(
)
11. Shock Level/Electronic Fence Level Decrease button.(
)
1.Charging
1.1 Use the included USB cable to fully charge the collar and remote control at 5V.
1.2 When the remote control is fully charged, the battery display is full.
1.3 When the collar is fully charged, the red light turns green. It fully charges in about two hours.
1.4 The battery level is shown on the remote control screen.The battery capacity of the collar cannot display on the remote screen after multiple collars are connected at the same time, when switching to a single dog, eg collar 3, the battery of the corresponding collar 3 will be displayed.
2.Collar On/Off
2.1 Short press the power button（） for 1 second, the collar will beep and vibrate to turn on.
2.2 After it powers on, the green light flashes once for 2 secs, automatically enter the sleep state if it is not used for 6 minutes, and the green light flashes once for 6 secs.
2.3 Press and hold for 2 seconds to power off.
3.Remote control On/Off
3.1 Long press the button（）for 2 seconds to turn on/off. There will be a beep and the screen will light up.
3.2 Long press the button（） for 2 seconds, a beep will be heard and the display will turn off.
4.Keyboard lock
4.1 Short press to lock the button（）, and then short press to unlock.
4.2 Recommended to lock the buttons when not in use to prevent misuse.
5.Pairing(One-to-one has been paired in the factory, you can use it directly)
5.1 In the remote controller's power-on state, long-press the Channel Switch button(） for 3 seconds until the icon starts flashing, and the remote controller enters pairing mode.
5.2 Then, short press this button () to select the receiver you want to pair with (the flashing icon indicates it's in pairing mode). Proceed to set up the receiver.
5.3 To put the receiver in pairing mode while it's powered off, long-press the Power button for 3 seconds until you see the indicator light flashing red and green. Release the button, and the receiver will enter pairing mode. Note: The receiver's pairing mode is active for 30 seconds; if the time is exceeded, you need to power off and retry.
5.4 Press the Sound Command button on the remote controller ( ) to confirm pairing. It will emit a beep sound to indicate successful pairing.
6. Cancel pairing
6.1 Long-press the Channel Switch button(
) on the remote controller for 3 seconds until the icon starts flashing. Then short press the switch button ()to select the receiver you want to cancel pairing with.
6.2 Short press the Shock button() to Delete Pairing, and then Press the Vibration button() to exit the pairing mode.
7.Pairing with multiple collars
Repeat the above operations, you can continue to pair other collars.
7.1 One channel has one collar, and multiple collars cannot be connected to the same channel.
7.2 After all four channels are paired, you can press the channel switch button（）to select 1 to 4 channels to control a single collars, or control all collars at the same time.
7.3 Vibration and shock levels can be individually adjusted when controlling a single collar.All functions are available.
7.4 Special Note:When controlling multiple collars at the same time, the vibration level is the same, and the electric shock function is turned off(X1/X2 model).The electric shock function at level 1(X3 Model).
8.Beep tone command
8.1 Short press ( ）button on the remote controller, and the receiver will emit a beep sound.
8.2 Long press ( ）button, and the receiver will continuously emit sounds.
9.Vibration intensity adjustment
9.1 Press the Vibration Level Decrease button() , and the vibration level will decrease from level 9 to level 0.
9.2 Press the Vibration Level Increase button (), and the vibration level will increase from level 0 to level 9.
9.3 Level 0 means no vibration, and level 9 is the strongest vibration.
10.Vibration command
10.1 Short press the vibration button（）and the collar will vibrate once.
10.2 Long press the vibration button（）,the collar will vibrate continuously and will stop after 8 seconds.
10.3 When controlling multiple collars at the same time, the vibration level is the current set value.
11.Shock intensity adjustment
11.1 Press the Shock Level Increase button (▲)on the remote controller, and the shock level will increase from level 0 to level 30.
11.2 Press the Shock Level Decrease button() on the remote controller, and the shock level will decrease from level 30 to level 0.
11.3 Level 0 means no shock, and level 30 is the strongest shock
11.4 It is recommended to start training the dog at level 1 and observe the dog's reaction before gradually increasing the intensity.
12.Shock command
12.1 Short press the electric shock button（）and there will be an electric shock for one second.
12.2 Long press the electric shock button（）and the electric shock will stop after 8 seconds.
12.3 Release the shock button and press the shock button again to activate the shock.
13. Electronic fence function (X3 model only).
It allows you to set a distance limit for your dog to roam freely and provides an automatic warning if your dog exceeds this limit. Here is a guide on how to use this function:
13.1 To enter the electronic fence mode: press the Function Select button（）.The electronic fence icon will be displayed（
）.
13.2 To exit the electronic fence mode: press the Function Select button（） again. The electronic fence icon will disappear （）.
Tips:When not using the electronic fence function, it is recommended to exit the electronic fence function to save power.
13.2.Adjust the distance levels:
To adjust the electronic fence distance: while in the electronic fence mode, press the (▲) button. The electronic fence level will increase from level 1 to level 14. Press the () button to decrease the electronic fence level from level 14 to level 1.
13.3.Distance levels:
The following table shows the distance in meters and feet for each level of the electronic fence.
|
Levels |
Distance(meters) |
Distance(feet) |
|
1 |
8 |
25 |
|
2 |
15 |
50 |
|
3 |
30 |
100 |
|
4 |
45 |
150 |
|
5 |
60 |
200 |
|
6 |
75 |
250 |
|
7 |
90 |
300 |
|
8 |
105 |
350 |
|
9 |
120 |
400 |
|
10 |
135 |
450 |
|
11 |
150 |
500 |
|
12 |
240 |
800 |
|
13 |
300 |
1000 |
|
14 |
1050 |
3500 |
The distance levels provided are based on measurements taken in open areas and are intended for reference purposes only. Due to variations in the surrounding environment, the actual effective distance may vary.
13.4 Preset Operations (Remote Controller can also be operated in Fence Mode):Before entering the fence mode, you must set the levels as follows:
13.4.1 For 1 dog: Both vibration and shock levels can be set
13.4.2 For 2-4 dogs: Only vibration level needs to be set, and the shock level cannot be adjusted (it remains at level 1 by default).
13.4.3 After setting the vibration level, you must press the Vibration button on the remote controller once to save the settings before entering the electronic fence mode. In the electronic fence mode, you cannot set the vibration and shock levels.
While in the electronic fence mode, you can use all the training functions of the remote controller, including sound, vibration, and shock. These functions will affect all collars within the electronic fence. When controlling multiple dogs, the automatic shock warning for going beyond the range is disabled by default, and the manual shock level is set to 1 by default.
|
Level Status in Electronic Fence Mode/Training Mode |
||||
|
Controlled Quantity |
1 Dog |
2 Dogs |
3 Dogs |
4 Dogs |
|
Vibration level |
Pre-set Level |
Pre-set Level（Every dog is at the same level） |
Pre-set Level（Every dog is at the same level） |
Pre-set Level（Every dog is at the same level） |
|
shock level |
Pre-set Level |
Default level 1 (cannot be changed) |
Default level 1 (cannot be changed) |
Default level 1 (cannot be changed) |
13.5.Automatic warning function:
When the collar exceeds the distance limit, there will be a warning. The remote control will emit beep sounds until the dog returns to the distance limit.And the collar will automatically emit three beep, each with a one-second interval. If the dog still does not return to the distance limit after this, the collar will emit five beeps and vibration warnings, each with a five-second interval, then the collar will stop warning. The shock function is turned off by default during the automatic warning. The default vibration level is 5, which can be preset.
13.6.Notes:
-When the dog exceeds the distance limit, the collar will be eight warnings in total (3 beep sounds and 5 beep sounds with vibration), followed by another round of warnings if the dog exceeds the distance limit again.
-The automatic warning function does not include shock function to ensure the safety of the dog. If you need to use the shock function, you can operate it manually using the remote control. If the automatic warning function is ineffective for controlling multiple dogs, you can exit the electronic fence mode and choose the specific collar to issue a sound/vibration/shock warning. If controlling only one dog, you can directly operate the training functions on the remote control for warning.
13.7.Tips:
-Always exit the electronic fence mode when not in use to save battery life.
-It is recommended to use the vibration function first before using the shock function during training.
-When using the electronic fence function, make sure the collar is properly fitted to your dog for optimal performance.
Post time: Oct-20-2023
